9TH SEPTEMBER — EA FC 27 AI GENERATOR UPDATE

Evilbot V8 – Call of Duty: Black Ops 7 Cronus Zen Script

ultimate
Call of Duty: Black Ops 7
Evilbot V8
Call of Duty: Black Ops 7
Mod Menu
Guides
My Image

Evilbot V8

Cronus Zen Master

Script details

Access
ultimate
Download format
.GPC
Supported platforms
cross-platform
Version
V8
Listing updated

Evilbot V8 is a Call of Duty: Black Ops 7 Zen script by Cronus Zen Master. Explore its download and setup information below.

This is a Call Of Duty Black Ops 7 Cronus Zen Script developed by Cronus Zen Master.

Includes mods:

  • Aim Assist
  • Anti Drift
  • Anti Recoil
  • Crouch
  • Ghost Tracker
  • Hair Trigger
  • Weapon Swap

Features

Mod Menu

This Script comes with a customizable Mod Menu

Guides

This script includes an instruction guide

Guides

Features

  • Full-featured mod menu with per‑profile Aim Assist & Anti‑Recoil
  • Three main categories: Aim Assist, Anti‑Recoil, Configuration
  • All settings are automatically saved when you exit the menu
  • VM Speed is now AUTO-DETECTED per console/controller (no manual setup)
  • Wait timings auto-scale so shared settings feel identical cross-platform


Opening the Menu

  • Hold L2 / LT + Press OPTIONS / MENU (≡ or ☰) — PS / Xbox respectively


Main Menu Navigation

  • UP / DOWN: Select category (Aim Assist, Anti‑Recoil, Config)
  • CROSS / A: Enter the selected category
  • CIRCLE / B: Save settings and exit to the title screen


Mod Menu (inside a category)

  • LEFT / RIGHT: Scroll through the mods available in that category
  • UP / DOWN: Adjust the value of the currently selected mod (Toggles: single press; Numeric: hold for rapid scrolling)
  • CIRCLE / B: Return to the Main Menu (settings are saved)


Custom Button Layout

  • Set Button Layout to "Custom", then press CROSS / A
  • LEFT / RIGHT: Move between actions (D-pad only)
  • RIGHT on last action: Save mapping and return to title (Circle/B is mappable and will not exit the mapper)


Quick Actions (while the menu is closed)

  • L2 / LT + RIGHT ($\rightarrow$): Cycle weapon profile (Primary $\leftrightarrow$ Secondary $\leftrightarrow$ Ground Loot) & Print to OLED
  • Tap TRIANGLE / Y (Swap Button): Cycle weapon profile (Primary $\leftrightarrow$ Secondary ONLY) & Print to OLED
  • L2 / LT + SHARE / BACK: Toggle the entire script ON / OFF (kill switch)
  • L2 / LT + R1 / RB + UP: Magnet Strength +1 (2.5s OLED feedback)
  • L2 / LT + R1 / RB + DOWN: Magnet Strength −1 (2.5s OLED feedback)
  • L2 / LT + R1 / RB + LEFT: Magnet Speed −5 (2.5s OLED feedback)
  • L2 / LT + R1 / RB + RIGHT: Magnet Speed +5 (2.5s OLED feedback)
  • L2 / LT + L1 / LB + LEFT: Previous Zen Polar parameter
  • L2 / LT + L1 / LB + RIGHT: Next Zen Polar parameter
  • L2 / LT + L1 / LB + UP: Zen Polar value +1 (2.5s OLED feedback)
  • L2 / LT + L1 / LB + DOWN: Zen Polar value −1 (2.5s OLED feedback)


Aim Assist Presets (per profile)

  • In Aim Assist category $\rightarrow$ "Presets" mod
  • UP / DOWN cycles through: Disabled $\rightarrow$ Balanced $\rightarrow$ Aggressive $\rightarrow$ Smooth $\rightarrow$ Sticky
  • Selecting any preset EXCEPT "Disabled" automatically turns Zen Polar ON for the current profile and applies all Aim Assist values.
  • Selecting "Disabled" turns Zen Polar OFF for the current profile.
  • Each profile (Primary / Secondary / Ground Loot) remembers its own preset.
  • Strength presets span 7 (Smooth) to 15 (Aggressive).


Additional Information

  • Tip: All controller inputs are blocked while the menu is open to prevent accidental presses.
  • All settings are automatically saved when you exit via CIRCLE / B.


Installation & setup

Follow these steps to install the GPC download on your Cronus Zen.

Full installation guide
  1. Download the script

    Use the download button on this page and save the .gpc file to your computer.

  2. Connect your Cronus Zen

    Open Zen Studio Live in Chrome or Edge.

    • Connect your Cronus Zen through the PROG port and select 'Connect Device'.
  3. Open the script in the Editor tab

    Drag the downloaded .gpc file into the 'Editor' tab.

  4. Add the script to a device slot

    Go to the Device tab, select MY SCRIPTS at the top right, then drag the chosen .gpc file into an empty slot.

  5. Program the Cronus Zen

    Click the flashing orange Program button at the top to save the script to your Zen.

  6. Connect, select your slot and test

    After programming finishes, connect the Zen to your console or PC using your platform’s connection setup. Select the installed script’s slot, then follow the creator’s button layout and starting values. Test before changing settings, and adjust one value at a time.

Need help with setup?

If the Zen is not detected, check the PROG connection and use a USB cable that supports data. If a GPC file fails to compile, check that the download is complete and that it supports your version of Zen Studio.

Evilbot V8: common questions

How do I install Evilbot V8?

This download is a GPC script. Follow the numbered instructions above to open it in Zen Studio, assign a device slot and program your Zen.

What access do I need for Evilbot V8?

This script is listed in the ultimate library. Sign in with a plan that includes this tier; your download button shows the access available to your account.

Where can I find settings for Evilbot V8?

The creator’s guide is included on this page. Sign in with the required access to view them, and match the script to your in-game settings before making adjustments.

Support Chat

Enlarged image

Click anywhere or press Escape to close

Script Preview